Yes. A-1 Plumbing & Gas provides 24/7 emergency plumbing service across Naples, Bonita Springs, Fort Myers, and the surrounding Southwest Florida area. Call (239) 699-3144 any time, day or night.
What areas in Florida do you serve?
We serve Naples, Bonita Springs, Marco Island, Estero, Fort Myers, Golden Gate, and North Naples, covering the greater Naples metro and Lee County.
Are you licensed and insured?
Yes. A-1 Plumbing & Gas is fully licensed and insured under Florida State License #CFC1430079.
Do you handle both plumbing and gas work?
Yes. We install and service natural gas and LP gas lines for appliances, pool heaters, outdoor kitchens, generators, and water heaters in addition to all standard residential plumbing services.
Can you install a whole-home water filtration or reverse osmosis system?
Yes. We install and service whole-home water filtration systems and reverse osmosis drinking water systems throughout Southwest Florida. Florida's hard water makes filtration a popular upgrade for our customers.
How quickly can you respond to a leak or burst pipe?
For active leaks, burst pipes, and water emergencies in our service area, we dispatch as quickly as possible, often the same day or within a few hours during business hours, and on a true 24/7 basis for emergencies.
Plumbing Repairs FAQs
Do you offer same-day plumbing repair appointments?
Yes, in most cases. Call us at (239) 699-3144 and our office will work to dispatch a tech the same day across Collier and Lee County.
How much does a plumbing repair cost?
It depends on the job. Every visit starts with a free, on-site estimate so you know the cost before we start.
Do you charge for after-hours emergency service?
After-hours dispatch is billed at our emergency rate, which we will explain over the phone before sending a tech.
Are your plumbers licensed and insured?
Yes. We are fully licensed under Florida State License #CFC1430079 and insured for both residential and commercial work.
Do you handle commercial plumbing repairs?
Yes. We service residential homes, condos, restaurants, and commercial buildings throughout Southwest Florida.
My water bill jumped but I cannot find a leak. What now?
Start with the toilets, because a silently running flapper is the most common cause and it leaves no visible water. If the toilets check out, the next step is a meter test: shut every fixture off and watch whether the meter still moves. If it does, the leak is in the supply somewhere, and that is worth locating properly before it finds a wall.
Can you fix a faucet or do I have to replace the whole thing?
Often we can fix it. Most faucets fail at the cartridge or the O-rings, and those are replaceable parts on any decent unit. Where we will tell you to replace is when the body is corroded or the finish is already going, because a new cartridge in a failing faucet buys months rather than years.
Do you work on homes in condo and HOA communities?
Yes. A lot of our Naples and Bonita Springs work is in condo and HOA communities, where plumbing is often shared between units and the association has rules about shutoffs and scheduling. We are used to coordinating with property managers and working within building access windows.
Yes. Generator installs are one of our most common gas projects, especially in Lee County after Hurricane Ian. We run the line from the meter or tank to the generator, coordinate with the electrician, pull the permit, and pressure-test the line before activation.
Can I get a gas line run to my outdoor kitchen or pool heater?
Yes. Both are common installs in Naples, Bonita Springs, and Estero. We run the line, install the connection, pressure-test, and pull the permit. The cost depends on the distance from the meter to the new appliance and whether the line runs through walls, slab, or yard.
My house does not have natural gas service. Can I still use gas appliances?
Yes, with LP propane. We install propane tanks (underground or above-ground) and the gas line from the tank to your appliances. This is common in Golden Gate, rural Collier County, and parts of Estero where natural gas service does not reach.
I smell gas in my home. What should I do?
Leave the house first. Do not flip light switches, do not use phones inside, and do not start any appliances. Once outside, call your gas utility from a safe distance, then call us at (239) 699-3144. We will inspect, locate, and repair the leak.
Do you handle gas water heater installs?
Yes. We install gas tank and gas tankless water heaters and handle both the plumbing and the gas line work in one visit. Our team is Uponor Certified on the water side and licensed on the gas side.
Can you service my restaurant or commercial kitchen gas system?
Yes. We service restaurants and commercial kitchens across Collier and Lee County. Restaurant gas work has its own code requirements and we handle the permitting and inspection process.
Do I need a permit to add a gas line?
Yes, gas work is permitted in Collier and Lee County, and that is a good thing for you. The permit brings an inspection, and the inspection is independent confirmation that the line was installed and pressure-tested correctly. We pull the permit as part of the job.
Can you run gas for a whole-house generator?
Yes. Generator lines are a large share of our gas work, and demand for them rose sharply across Lee and Collier County after Hurricane Ian. We size and run the line, pressure-test it, and coordinate with your electrician on the connection side.
What if natural gas is not available on my street?
Then propane does the same work. LP tanks, above ground or buried, feed ranges, pool heaters, generators, outdoor kitchens, and tankless water heaters the same way natural gas does. Parts of Golden Gate, Estero, and rural Collier County run on propane for exactly this reason.
A standard drain cleaning service for a single clog runs in a predictable range. Recurring clogs, hydro jetting jobs, and sewer line work cost more because they involve more equipment and time. We quote every job up front before work starts so you see the price first.
What is hydro jetting and when do I need it?
Hydro jetting uses high-pressure water (up to 4,000 PSI) to scour the inside of a drain or sewer line clean. It is the right tool for heavy grease, scale, root intrusion, and any clog a snake will not fully clear. For a single kitchen sink clog, hydro jetting is overkill. For a recurring main line backup, it is often the right answer.
Do you actually record the drain camera footage?
Yes. Every camera inspection includes a recording you keep. It is useful for insurance claims, real estate disclosures, and confirming the repair worked. Some customers ask for the footage on a USB drive, others want it emailed. Both are fine.
My drain clogs every few months. Is something wrong with the line itself?
Usually yes. Recurring clogs in the same fixture or line are almost always a sign the pipe has a problem: root intrusion, broken section, low spot, scale buildup, or polybutylene degradation. Snaking the line again will not fix it. We run a camera, find the cause, and quote the actual repair.
Can drain cleaning damage my pipes?
Done correctly, no. A snake the wrong size or hydro jetting at the wrong pressure can damage older or already-compromised pipes, which is why we run a camera first on anything that looks risky. On modern PVC and cast iron, both techniques are safe.
Do you handle commercial drain cleaning and grease traps?
Yes. We service restaurants, offices, and commercial properties across Collier and Lee County, including grease trap cleaning and pumping. We schedule preventive maintenance for commercial kitchens so the call does not come during dinner service.
The same drain keeps clogging. Why does clearing it not last?
Because clearing a blockage and fixing its cause are two different jobs. A drain that clogs in the same spot repeatedly usually has a physical reason: roots at a joint, a low section holding water, or a pipe that has scaled down to a fraction of its diameter. A camera finds which one it is, and until you know that you are buying the same service call over and over.
Is hydro jetting safe for older pipes?
It depends on the pipe, which is why we look before we jet. Jetting is excellent in sound cast iron and PVC and it removes grease and root mass a cable only bores a hole through. In a line that is already channeled or cracked, jetting is not the right tool and we will tell you so rather than run it.
Do chemical drain cleaners help?
Rarely, and they can make things worse. They do little against roots or a collapsed section, they sit in the trap generating heat, and they are hard on older cast iron and on the person who opens that line up next. If a plunger has not done it, the problem is usually mechanical.
Tank water heaters in Southwest Florida typically last 8 to 12 years. Coastal homes near saltwater air see the lower end of that range. Tankless units last longer, often 15 to 20 years with regular descaling. Hard water and lack of annual maintenance are the two biggest factors that shorten life.
Should I replace my tank water heater with a tankless?
It depends. Tankless gas units make sense for homes with consistently high hot water demand, available gas service, and a willingness to invest more up front for long-term efficiency. Tankless is not always the right call for low-demand homes or all-electric properties. We walk through the math during the site visit.
What size water heater do I need for my Naples home?
For tank units, a two-person home is fine with 30 to 40 gallons, a typical family of four usually wants 50, and larger families or multi-bathroom homes with high simultaneous use need 65 to 80 gallons. Tankless sizing is different and depends on flow rate and groundwater temperature. We size every install during the quote, not after.
What brands of water heater do you install?
Rheem, Navien, AO Smith, Bradford White, and Bosch tankless. We recommend the brand that fits your home, budget, and space rather than pushing one line.
My water heater is leaking. Is that an emergency?
A small drip at the relief valve is usually not an emergency, but it does need to be checked soon. An active leak from the tank itself or from connections at the top is an emergency, especially if the unit sits in a garage near drywall or in a closet near interior space. Shut off the water supply to the unit and call us.
Do you flush water heaters and replace anode rods?
Yes. Annual flushing extends tank life noticeably in Florida's hard water. Anode rod replacement adds even more time and is one of the cheapest maintenance items you can do. We offer both as standalone visits and as part of an annual maintenance plan.
How long should a water heater last in Southwest Florida?
Less than the brochure suggests, because our water is hard. Minerals accelerate anode rod consumption and build sediment on the tank bottom, and both shorten service life. Flushing the tank and checking the anode are the two things that actually extend it, and both are cheap next to a replacement.
Why does my water heater make a popping or rumbling noise?
That is sediment. Minerals settle into a layer on the tank floor, water gets trapped underneath, and the sound is that water boiling through the deposit. It means the burner is heating sediment instead of water, so the unit is working harder and the bottom of the tank is taking heat it was not meant to take.
Is tankless worth it here?
More often than in most of the country, because Florida groundwater comes in warm and a tankless unit has less temperature rise to produce. The real question in a retrofit is usually the gas line, since tankless units need one sized for their demand. We will look at what you have before recommending anything.
How fast can you respond to a plumbing emergency in Naples?
For active emergencies inside our service area (Collier and Lee County), we dispatch as fast as the closest available tech can reach the address. During business hours that is often within one to two hours. After hours, a real person answers the phone immediately and we dispatch a tech for true emergencies the same night.
What counts as a plumbing emergency?
Active leaks, burst pipes, sewage backups, no hot water before guests arrive, suspected gas leaks, water heater failures with active water damage, and any situation where the water has to stay off until we arrive. If you are not sure whether it qualifies, call and ask. Our office can triage in under a minute.
Do you charge extra for nights, weekends, or holidays?
We quote every emergency job up front before work begins. You see the price and approve it before we open anything. There are no surprise after-hours charges added to the bill at the end.
What should I do before you arrive for a leak emergency?
If you can safely reach the main water shutoff to the house, turn it off. If the leak is at a specific fixture, the local shutoff under the sink or behind the toilet is enough. For water heater leaks, shut the cold supply line into the unit and, for gas heaters, turn the gas off if you can do so safely. Then call us. We can walk you through this on the phone.
Do you handle gas leak emergencies?
Yes, our team is fully licensed for natural gas and LP propane. If you smell gas, leave the house first, call your gas utility from outside, then call us. We can isolate, repair, and pressure-test the line on the same visit in most cases.
Can you handle a condo or commercial emergency?
Yes. We have responded to full condo complex water restorations on weekends and handle commercial plumbing emergencies for restaurants and offices across Collier and Lee County. Call (239) 699-3144 and tell the dispatcher it is a multi-unit or commercial situation so we send the right crew.
Where is my main water shutoff?
On most Southwest Florida slab homes it is on an exterior wall on the street side of the house, often near a hose bib, and there is a second valve in the meter box at the curb. Go find yours before you need it. The gap between a five minute leak and a fifty minute leak is usually just knowing where that valve is.
Do you actually answer the phone at night?
Yes. A-1 Plumbing & Gas runs 24/7 emergency dispatch at (239) 699-3144 across Naples, Bonita Springs, Fort Myers and the surrounding area. Several of our Google reviews mention reaching a live person on a weekend, which is the point of running the line that way.
I am away for the season. How do I keep the house safe?
Shut the main and drain the system before you close it up. Most of the failures we find in October and November started months earlier as a slow weep behind a wall, in a house with nobody in it. Ten minutes on the way out prevents the majority of them.
Do I need to replace my sewer line or can it be repaired?
It depends on the damage. A small crack or root intrusion in a single section often allows a spot repair. Widespread damage, collapsed pipe, or old polybutylene material usually means replacement.
How long does a sewer line replacement take?
Most residential sewer line replacements finish in one to three days, depending on length and access.
Do you handle the permits?
Yes. We pull all required permits with the county and inspect to code.
Will my yard be torn up?
Some excavation is unavoidable for a full replacement. We work to minimize disruption and restore the work area.
What is a clean-out and why do I need one?
A clean-out is an access point on the sewer line that lets a plumber service the line without entering the home. Most modern installs include one near the property line.
How do I know if I need a repair or a full replacement?
A camera inspection settles it. One offset joint or a single root intrusion in an otherwise sound line is a spot repair. A cast iron line that has corroded through along its length is not, and no amount of cleaning will hold it. We would rather show you the footage and let you see what we are seeing.
Multiple drains are backing up at once. What does that mean?
When several fixtures back up together the blockage is usually past the point where those lines join, which means the main rather than any one branch. Stop running water everywhere in the house, including appliances, and call us. Continuing to run water adds to whatever is coming back up.
My house was built in the 1960s. Should I be worried about the sewer line?
It is worth looking at. Homes from that era in Naples and Fort Myers were generally plumbed with cast iron under the slab, and cast iron has a finite life that many of those lines are now at the end of. Worried is the wrong word, informed is the right one, and a camera inspection is how you get there.
How do you find a leak inside a wall or under a slab?
We use acoustic listening equipment, thermal imaging, and pressure testing to pinpoint the leak before any demo.
What is a slab leak?
A slab leak is a water line leak underneath the concrete foundation of your home. They often show up as warm spots on the floor, unexplained moisture, or a high water bill.
Will I have to break up my floor?
Sometimes a small section of slab needs to be opened to reach the leak. In other cases we can reroute the line and avoid the slab entirely.
How much does slab leak repair cost?
Costs vary widely based on location, length, and reroute options. Every slab leak job starts with a free estimate.
My water bill spiked but I cannot find a leak. Can you help?
Yes. Sudden bill spikes are one of the most common reasons we get leak detection calls. We will find the source.
How long does it take to find a hidden leak?
Locating usually takes a good deal less time than people expect, often under an hour, because the equipment narrows it down quickly once we know which line is losing pressure. The variable is access. A leak under a slab in the middle of a tiled living area takes longer to confirm than one in an accessible wall, and we confirm with a second method before anything opens.
Can a slab leak damage the foundation?
It can, and that is the real reason not to leave one running. Water escaping under a slab washes out the sand and fill the foundation bears on. The plumbing repair itself is straightforward. Soil that has been eroding for months is a bigger and more expensive problem, so the sooner a slab leak is found the smaller the whole thing stays.
Does homeowners insurance cover leak detection?
Policies vary and we are not the ones to tell you what yours covers, so read it or ask your agent. What we can do is give you documentation: the location of the leak, what failed, and what was done to repair it. Carriers generally want that in writing, and we provide it for your records on every leak call.
Yes, Naples municipal water meets federal safety standards. The reason most customers install filtration is not safety but quality: hard water minerals damage fixtures and appliances, chlorine affects taste and skin, and sediment builds up over time. Filtration improves water quality at every tap.
What is the difference between a water softener and a whole-home filtration system?
A water softener specifically targets hard minerals (calcium and magnesium) using salt-based ion exchange. A whole-home filtration system is broader and can include carbon for chlorine, sediment filters, and softening media all in one unit. For most Florida homes, a combination system is the right answer.
Do I need filtration if I have a well?
Almost always yes. Well water in our area often contains sulfur (rotten egg smell), iron (rust stains), sediment, and sometimes bacteria. A well-water filtration system handles all of it. We test the water first and size the system based on what is actually in the well.
How often does a filtration system need service?
Carbon filters last 6 to 12 months depending on use. Sediment pre-filters need changing more often, sometimes every 3 to 6 months. Softener media gets refilled or replaced on its own schedule. We offer annual maintenance plans that cover filter changes and system inspection.
Will a filtration system protect my water heater?
Yes, considerably. Hard water scale is the single biggest factor that shortens water heater life in Florida. Filtration upstream of the water heater can extend the life of the unit by years and reduce the cost of repairs over the same period.
How much does a whole-home filtration system cost in Naples?
It depends on the type of system, the home's water use, and whether you are on municipal water or a well. Basic systems are an affordable upgrade. Larger combination systems for high-demand households cost more. We test the water and quote the system before any install begins.
Will a filtration system fix my water pressure?
No, and an undersized one will make it worse. Filtration is about what is in the water rather than how hard it is pushing. A system sized correctly for your home is effectively neutral on pressure, while one too small for the fixture count becomes a restriction you feel every time two showers run at once. That sizing is the part worth getting right.
I am on a well in Golden Gate Estates. Is that different?
Yes, meaningfully. Well water here commonly brings iron and sulfur, which municipal supply does not, and those need media chosen specifically for them. Iron causes the orange staining on fixtures and laundry, sulfur causes the rotten egg smell. Neither is addressed by a softener alone, so a well system is generally a different build than a city water system.
How often does the filter media need to be replaced?
It depends on the stage and on how much water the household uses. Sediment pre-filters load up fastest, carbon has a capacity it eventually exhausts, and softener resin lasts years but needs salt kept up continuously. We install with a bypass valve so service never shuts water off to the house, and yearly maintenance is available if you would rather not track it.
It is gray (sometimes blue, sometimes black), plastic, and the supply lines under sinks look unlike modern PEX or copper. If your home was built between 1978 and 1995 in Florida and has its original plumbing, there is a real chance. We can confirm with a quick site visit at no charge.
How long does a whole-home repipe take?
Most residential repipes take 2 to 5 days depending on home size, layout, and whether drywall work is included. The water is off during certain phases of the work but not the entire time. We walk through the timeline before the job starts.
Will I have to move out during the repipe?
Almost never. We schedule the work so the water is only off during specific phases, usually for a few hours at a time. Most homeowners stay in the home through the entire repipe.
How much does a whole-home repipe cost in Naples?
It depends on home size, number of bathrooms, slab vs crawlspace, single story vs multi-story, and whether drywall closure is included. A smaller single-story home is a different number than a 4,000-square-foot two-story with three baths. Every repipe gets a written quote after a site visit so the price is exact, not estimated.
What is the warranty on a repipe?
The Uponor PEX itself is rated for 50 to 100 years in residential service. Our installation work carries our standard warranty. We back the job, and the manufacturer backs the material.
Can you handle the drywall repair after the repipe?
We coordinate drywall closure as part of the repipe. Some customers want us to handle it end-to-end, others have a contractor they prefer for the drywall. Both options work. The repipe quote includes whichever path you choose.
Will I have water during the repipe?
Yes, every evening and every night. Water is shut off during working hours while lines are being run and restored before the crew leaves for the day. Most homeowners stay in the house for the duration. If a particular job is going to be an exception to that, we tell you before the work is scheduled rather than after it starts.
How much drywall gets opened?
Less than people picture, because PEX runs in long continuous lengths and needs far fewer access points than a rigid system would. We walk the routing with you before anything opens so you know where the holes will be. Closure work is coordinated as part of the job rather than left for you to arrange afterward.
Can you repipe just part of the house?
Yes, and sometimes that is the honest recommendation. Rerouting a single slab leak or replacing one failing branch is a far smaller job than a whole-home repipe and it is the right call when the rest of the system is sound. Where we will recommend the full repipe is polybutylene, or copper that has started pinholing in more than one place.
What does a reverse osmosis system actually remove?
RO systems remove most dissolved solids, chlorine, fluoride, lead, and many contaminants. They produce noticeably cleaner, better-tasting water.
Do I need an RO system if I already have whole-home filtration?
Whole-home filtration covers showers and laundry. RO is the best in-class option specifically for drinking water at the tap.
How often do filters need replacement?
Pre-filters usually need replacement every 6 to 12 months. The membrane lasts 2 to 3 years.
Will it slow down my water pressure?
RO systems have a small storage tank to handle pressure. Flow at the dedicated faucet is steady but slightly slower than your main tap, by design.
Can you connect it to my fridge or ice maker?
Yes. We can run a line to your refrigerator and ice maker as part of the install.
Does an RO system waste water?
It produces some wastewater, yes. That is inherent to how the membrane works: some water carries the rejected dissolved solids to the drain rather than to your glass. At the few gallons a day a kitchen system produces it is a modest amount, and it is also the reason RO is a drinking water solution rather than a whole-house one.
Will RO water work for my coffee maker and ice maker?
It works well for both, and the difference in ice is usually the thing people notice first. Ice made from untreated hard water goes cloudy and picks up taste. Running a line to the refrigerator at install time is straightforward while the cabinet is already open, so it is worth deciding on before rather than after.
Is there room under my sink for one?
Usually, but it is worth checking rather than assuming. The unit and its storage tank need space alongside the disposal, the trap, and whatever is already stored there. In a tighter cabinet the tank can sit in an adjacent base cabinet with a line run across. We confirm the space at the site check before anything is ordered.
My main shutoff valve does not work. Can you replace it?
Yes. Replacing a failed main shutoff is one of the most common service calls we get and is usually a same-visit fix.
How do I know if my main water line is leaking underground?
Wet spots in the yard, an unexplained spike on your water bill, or low pressure across the whole home are the typical signs. We can confirm with a pressure test.
Do you replace galvanized water lines?
Yes. Galvanized lines corrode from the inside and restrict flow. Replacement with copper or PEX is the standard fix.
How long does a main water line replacement take?
Most residential main line replacements finish in one day, including the excavation and restoration of the work area.
Is a hose bib repair something I should call about?
Yes. A leaking hose bib wastes water and can damage exterior walls. They are a quick repair for our techs.
There is a wet spot in my yard. Is that my line or the utility line?
The meter is the dividing line. From the meter to the house is yours, from the meter to the main is the utility. A wet patch on the house side of the meter is generally yours to repair. Water travels along the trench before it surfaces, though, so the wet spot is not necessarily above the break, which is why we pressure test and locate rather than dig on appearances.
What is a pressure regulator and how do I know mine failed?
It is the valve that steps street pressure down to something your plumbing is built for. When one fails it usually fails open, so the house sees full street pressure. The signs are fixtures that suddenly bang or hammer, supply connections weeping, and a toilet that runs after every flush. It is a contained repair and worth doing quickly, because high pressure is hard on everything at once.
Do you handle the digging for a main line replacement?
Yes, excavation is done in-house rather than subcontracted. That means one crew, one schedule, and one company answering for the restoration when the ground goes back. It also keeps the trench as narrow as the job allows, because the people digging are the same people who have to work in it.
Should I buy the fixture myself or have you supply it?
Either works. We work with our supplier network or install fixtures you have already bought. For high-end brands, we can recommend models and finishes.
Do you install garbage disposals?
Yes. We install and replace all major brands of garbage disposals.
Can you do a bathroom remodel?
Yes. We handle the plumbing side of bathroom and kitchen remodels, including rough-in, fixture install, and final trim.
Will my old shutoff valves work for a new faucet?
Often yes, but we replace any shutoff valve that drips or sticks during the install.
Do you install bidet seats?
Yes. Bidet seats are a quick install and usually require an outlet near the toilet plus a connection to the existing supply line.
Can I keep my existing shower trim if I only need the valve fixed?
Often yes. The valve body lives in the wall and the trim is the visible part, and matching new trim to an existing body is possible more frequently than people assume. That matters because replacing the body means opening tile. Tell us the brand and we will check compatibility before anyone picks up a grinder.
Why does my brand new faucet already have low pressure?
Check the aerator first. Our water is hard, scale collects in that screen faster than anywhere else in the fixture, and it happens on a new faucet as readily as an old one. Unscrewing and rinsing it takes a couple of minutes and solves it most of the time. If pressure is low at every fixture rather than one, that is a different problem and worth a look.
Do you replace the shutoff valves when you install a fixture?
Yes, along with the supply lines, and we would rather you know that going in. The valve under a sink in an older home has often not been turned in decades and will not reliably reseal once it is. Reusing it to save a few dollars on install day is how a fixture swap turns into a leak six months later.